The EZ Tone Door Chime never needs batteries or electricity and it can easily be installed on all types of doors and jambs. When the door is opened, a magnetic striker hits the toned chime bar and produces a pleasant, audible tone. It can be used in both commercial and residential applications. Once installed no maintenance is ever required.
The EZTone is designed for doors that swing only one direction.
Easy instructions, mounting templates and hardware included.
EZTone customers include, Subway, Blockbuster, Winn-Dixie, US Postal Service, Kentucky Fried Chicken, Dollar General Stores, Little Caesars, and many professional offices nationwide. The E-Z Tone Door Chime can usually be installed within 15 minutes, and has a long, maintenance free life.
For more information visit our entry alerts page. #DoorChimes, #EntryAlerts #ALERTTYPE https://www.entryalertproducts.com/ez-tone-entrance-alert-door-chime-beige-light-gray-color/
Friday, December 29, 2017
EZ Tone Entrance Alert Door Chime, Beige / Light Gray Color
Entry Alert Invisible Beam System With Chime, Seco-Larm
Safety sensor for garage doors
Overhead doors security sensor
Entry detection for store front
- Safety sensor for garage doors
- Overhead doors security sensor
- Entry detection for store front
- Other applications: offices, schools, warehouse, vehicle detection, etc.
- Retro-reflective design.
- Range: Up to 22 feet (7m)
- Perfect for monitoring an entrance or use as an entrance indicator.
- Will make "ding-dong" sound or siren sound when the beam is interrupted.
- Speaker volume can be adjusted or turned off.
- When in siren mode, sounding time is adjustable from 3 to 30 seconds.
- 9VDC adapter included.
- Cable (w/plugs) wire length is 33 feet (distance between sensor & speaker).
- All components plug into each other. No hard wiring required.
Includes the following:
- NIR retro-reflective sensor.
- Reflector.
- Speaker.
- 9VDC 200mA output adapter.
WIRELESS version of above unit now available: item 80-550
Product Info Sheet
Instructions #DoorAlarm, #EntryAlerts, #EntryMotionSensorDetection https://www.entryalertproducts.com/product/entry-alert-system-with-chime-seco-larm/
Multi-Purpose Programmable Timer Relay Module
This timer is easy to setup and use with all of our entry alert and driveway alarm products. Use the timer and optional higher current (500ma or 1 Amp) 12VDC adapter power supply to have higher power drawing accessories (up to 8 amps) activate for a specified length of time immediately after the sensor detects something and the alert receiver outputs an audible or visual alert. Programmable Timer Relay can be used on the 12VDC output of receivers or the Timer Relay can also be used on the Form C relay (NO/NC) channel/zone outputs of receivers to activate an accessory by channel/zone (additional 12VDC adapter power supply required for this application). Or use the timer to add a delay to the accessories activation. Timer activation or delay can be set from 1 second up to 60 minutes. With the easy to understand dip switches and versatility this timer allows you create the exact notification alert delay and or timed output (on) response you want. click for Data Sheet click for Product Instructions |
Thursday, December 28, 2017
Curtain / Barrier Photobeam Sensors, Multiple, Seco-Larm
This device requires separate sounder, alert or chime system (and power supply for sensor and possibly chime). See items 1-9 on our accessories page.
These infrared photobeam curtain/barrier sensors are perfect for installation in windows, doorways, skylights, fence tops, any place where space is limited.
Suitable for indoor and outdoor perimeter security, the trigger is programmable for simultaneous breaking of any single or 2 adjacent beams. The design features rugged aluminum construction, and an anti-tamper circuit for triggering an alarm if power is cut or the end cap is removed.
No synchronizing wires are required and the LED alignment indicator makes installation easy. L-brackets and mounting hardware are included.
Manufacturers Web site
Note: Requires seperate sounding device and power supply.
NOTE: This device is not a stand alone system or plug"n play installation. Minor low voltage wiring required and additional items required to use. #AlarmSystem, #AlarmSystems https://www.entryalertproducts.com/product/curtain-barrier-photobeam-sensors/
Wireless PIR Indoor Motion Sensor, Dakota IR-2500
The IR-2500 is the newest wireless PIR indoor motion alarm from Dakota Alert. With a wireless range of up to 2000 feet* and full compatibility with any of our 2500 Series transmitters or receivers, the IR-2500 will allow you to monitor many indoor locations that were difficult before. The passive infra red detector is able to monitor an area up to 100º wide. With the integral mask, the detection area can be narrowed down to 20º or anywhere in between. With the swivel mount, the IR-2500 sensor can be adjusted right to left up to 80º and up and down up to 50º. With three different sensitivity settings, the IR-2500 can detect a person up to 12 feet, 25 feet or 40 feet away. The sensor can also be set to flash an LED or stay dark when a signal is sent. The IR-2500 is powered by one 9 volt battery and will have a battery life of about 12 months under normal conditions. There is also a low battery alert to notify you when it is time to replace the battery. The IR-2500 is designed for indoor or light duty outdoor applications under an eave or awning or other protected location. Operating range -30º F to 120º F.
Motion Sensor Product Instructions #AlarmSystems, #MotionSensor https://www.entryalertproducts.com/product/indoor-motion-sensor-ir2500/
Wednesday, December 27, 2017
Motion Sensor/Transmitter for Rodann Driveway Entry Alert, TX-2000A
The outdoor weatherproof transmitter unit that can be either side or overhead mounted. A 9V replaceable battery is included and is already installed for your convenience. In the back of the unit there are six dip-switches. Numbers 1-4 control the communication security codes that must match the receiver. Numbers 5 & 6 on the transmitter identifies which of up to 4 transmitters (zones) is sending a driveway motion alert. There is an antenna that can rotate for optimal transmission to the receiver up to 1000" (LOS) or 600" recommended. The driveway beam projection at 25 feet is 1 foot square and at 50 feet it is 2 feet square. #AreaMotionActivation, #EntryWay https://www.entryalertproducts.com/product/motion-sensor-transmitter-for-rodann-driveway-entry-alert-tx-2000a/
Tuesday, December 26, 2017
12VDC Plug-in Regulated 1.0A Switching Power Supply
AC wall transformer/adapter has a 12VDC 1 AMP output to power our large sirens or multiple accessories. #AlarmSystems, #PowerSupplyAdapter https://www.entryalertproducts.com/product/adapter-12vdc-1-amp/
Siren, 15 watts, 12VDC, 110db
15 Watt 12VDC Siren is weatherproof with a 110db sound level. Simply connects to the relay output of an Alert Receiver. Requires 1 Amp adapter (60-301). Cone 3.5" diameter x 4" long. #AlarmSystems, #Siren https://www.entryalertproducts.com/product/siren-15-watts-12vdc-110db/
Monday, December 25, 2017
Happy Holidays
#HomeSecurity, #ResidentialSecuritySystem #Uncategorized https://www.entryalertproducts.com/happy-holidays/
Door / Window Sensor, Wireless Long Range, WD-434TL
|
Friday, December 22, 2017
Twin Photobeam Detector, In / Outdoor, Seco-Larm
This device requires separate sounder, alert or chime system (and power supply for sensor and possibly chime). See items 1-9 on our accessories page.
ENFORCER Long Range Photobeam Detectors are easy-to-install with laser beam alignment and provide extended range. Designed to provide reliable perimeter security both indoors and outdoors.
Product Info sheet
Installation Manual
Manufacturers Web site
Note: Requires separate sounding device and power supply.
NOTE: This device is not a stand alone system or plug’n play installation. Minor low voltage wiring required and additional items required to use.
Features
- Built-in laser beam alignment system speeds accurate, reliable positioning.
- Twin infrared beams provide reliable perimeter security, minimizing false alarms from falling leaves, birds, etc.
- Lensed optics reinforce beam strength & provide excellent immunity to false alarms due to rain, snow, mist, etc.
- Weatherproof, sunlight-filtering case for indoor & outdoor use.
- Anti-frost system so that beam functions even in extreme conditions.
- Automatic input power filtering with special noise rejection circuitry.
- N.C./N.O. alarm output.
- N.C. tamper circuit included.
- Non-polarized power inputs.
- Quick, easy installation with built-in laser beam alignment system.
- Interruption time adjustable for nearly all situations.
For more information visit our entry alerts page #HomeSecuritySystem, #SecuritySystems #ALERTTYPE https://www.entryalertproducts.com/twin-photobeam-detector-outdoor-seco-larm/
Siren, 15 watts, 12VDC, 110db
15 Watt 12VDC Siren is weatherproof with a 110db sound level. Simply connects to the relay output of an Alert Receiver. Requires 1 Amp adapter (60-301). Cone 3.5" diameter x 4" long. #AlarmSystems, #Siren https://www.entryalertproducts.com/product/siren-15-watts-12vdc-110db/
Optex TD-20U PIR Transmitter
The TD-20U is the battery-powered sensor transmitter for the RCTD-20U (Wireless 2000). The detection pattern is selectable, allowing for a 17 foot fan pattern or 50 foot beam pattern, and sends a signal back to the RC-20U chime box when compromised. The device is powered by a standard 9V battery (not included), and up to nine TD-20U"s can be added to one RC-20U receiver.
The TD-20 Sensor/Transmitter is a PIR detector which will detect both people and vehicles. This weatherproof wireless indoor/outdoor sensor transmitter mounts easily wherever you need to know of people or cars arriving or leaving, and sends a signal back to the Optex RC-20 Receiver (up to 2000") to alert you of visitors. It includes two detection patterns: fan (~17" semi-circle) or long range (at ~50" away from transmitter invisible beam size is 6" x 9" rectangular). The TD-20 is easily mounted behind a tree with its unique mounting capability.
Features
- Specially designed sensor mounts easily on walls, ceilings, fence posts, desktops, etc.
- Weatherproof design of sensor allows outdoor use.
- Two detection patterns: 50ft Long Range and 17ft. Fan Pattern.
- Detection pattern adjusts easily for perfect aiming.
- Transmission codes are preset at the factory with over 8 million possibilities, virtually eliminating the possibility of interference or cross-talk.
- All wireless transmitters have "dead spots" within their transmission range. TD-20"s improved antenna design greatly reduces "dead spots" to make installation easier and increase reliability.
- 1 RC-20 and up to 4 TD-20 can be installed around your home entrances for perimeter awareness.
Thursday, December 21, 2017
Home Security System Advice
Professional Advice On Your Home Security System Needs
No matter if you rent or own, you want to be safe. Perhaps you are unaware of how to secure your home. This article is your solution to help you choose the best home security system. Keep reading to learn what you can do.
Before leaving for vacation, turn off the ringers in your house. A burglar might hear your phone ring and ring and ring, then realize that you are not home to answer it.
If you do not know the person at your door, don"t open it. There are people who are going to be convincing, but they can just be professional thieves. Enforce a rule within your house that no one opens the door to unexpected people.
Before doing anything else, install new locks in your home. Not everyone who leaves your house will leave happy, and a fresh set of locks will protect you from both former residents and acquaintances of your own looking to cause mischief. Most locksmiths can accomplish the job within 24 hours.
Walls make the perfect hiding spot. You can hide small, valuable items inside the walls of your home. Just take advantage of the phone jack, electrical outlet or unused switch plate. If you have no unused plates, you can easily install false ones.
Do not let people on the street see valuable items in your home. While it may be nice to look out, burglars will see your valuables inside. Keep your curtains drawn to keep your valuable items safe.
While choosing your alarm system, ask about protection for windows and motion detection as well as doors. Burglars can gain entry through your windows as well. Every single entry point needs to have monitoring on it. This will help to keep your family safe.
Make sure the wires of your home security system are completely hidden. One of the ways an intruder can get around a security system is by disconnecting or cutting the wires. Make sure the wires are installed inside the walls of your home. This will make you much safer.
Before allowing someone into your house, be sure to carefully check their references. Perform a background check to learn about their criminal history, too. Avoid giving keys out to contractors, maids and repairmen.
When you are trying to hire a home security contractor, read all the small print on your contract before signing it. There may be hidden costs to doing business with them, including early termination fees and surprising equipment costs. You are going to want to avoid these kinds of hidden fees, so know about them up front.
Purchase a paper shredder to prevent your discarded papers from providing burglars with valuable information. Thieves may look through your garbage for information. If you can not afford to purchase a paper shredder, just rip the paper into smaller pieces.
Are your house numbers visible from the street? If an emergency happens, the police can"t get to the home as quick if your numbers are obscured in any way or are too small. Happily, it"s quick and easy to fix this problem.
Inquire about different choices for contract lengths available from the home security provider. Each will have its own pros and some cons, too. Longer agreements may cost less per month, but you may not be able to get out of the contract if you need to. Shorter contracts allow your greater freedom, however they usually cost more each month.
Don"t get spring latch locks. These locks can be opened easily with a credit card. Intruders just have to slide a card in between the latch and door for the lock to pop open. If your doors have locks that are spring latch, add a deadbolt for extra security.
Never place a key in an obvious spot. Is anybody really fooled by those fake rocks? Not likely. Another obvious location is underneath the doormat. This will be one of the first places that a burglar will look for your spare key. Talk to a neighbor or someone that you know to hold your key. If you cannot do that, try to be creative when it comes to hiding places.
A sliding glass door often presents a big challenge to home security. They can be unlocked very easily if you shake and lift them. If there is no security system on it, you should place a pipe inside the door channel. This will prevent the door from moving or becoming unlocked.
When it comes to locks, remember that you have to be able to lock it from both the inside and outside for maximum security. Deadbolts are the best option. Double key locks are good as well, since burglar can"t easily open them.
Now that you have a better understanding of home security, it is time to get started. Do not waste time and allow these ideas to slip away. They can help you put into effect your good intentions to make your home secure. The safer you feel, the better you will sleep, so don"t dawdle!
Home Security System
#HomeSecuritySystem, #SecuritySystems #SecurityArticles https://www.entryalertproducts.com/home-security-system-advice/Entry Way Alert Set. For outdoor or driveway applications, Rodann, RX/TX-2000A
Both transmitter and receiver have antennas that allow 360 degree rotation and pull away from sides of boxes. For best results in communication between transmitter and receiver it is ideal for the antennas to be on the same plane. Example: (If one antenna is pointing up in the vertical position, then the other antenna should be pointing up also. If one antenna is in the horizontal position, then the other antenna needs to be horizontal and pointing at each other for optimum reception). When it comes to distance in communication between transmitter and receiver environmental condition need to be considered. Line of sight without obstacles is ideal. Every tree, bush, fence, car, building in direct line of sight will reduce communication between units. These units should give you approximately 1000’. You may also add additional transmitters to one receiver or additional receivers to one transmitter.
TRANSMITTER
The outdoor weatherproof transmitter unit that can be either side or overhead mounted. A 9V replaceable battery is included and is already installed for your convenience. In the back of the unit there are six dip-switches. Numbers 1-4 control the communication security codes that must match the receiver. Numbers 5 & 6 on the transmitter identifies which of up to 4 transmitters (zones) is sending a driveway motion alert. There is an antenna that can rotate for optimal transmission to the receiver up to a realistic 1000 feet away. The driveway beam projection at 25 feet is 1 foot square and at 50 feet it is 2 feet square.
Additional wireless Sensor /Transmitters may be added (item 25-404).
RECEIVER
The indoor receiver has a plug-in 12VDC power supply with a 6 foot cord. The receiver may be placed on a counter top, table or hung on the wall. The electronic LED counter feature allows you to either count customers or count unexpected visitors / vehicles moving in your driveway. There is a reset button next to the counter, when pressed it will zero out the counter. This unit also has six dipswitches on the back of this unit. Numbers 1-4 must match transmitter. Number 5 controls the output of the 12VDC terminals on the back of the receiver with a one second or five second 12VDC output, Number 6 is not used. The terminal screws on the receiver back give you the option of adding a bell, buzzer, horn, siren, strobe or anything that is 12VDC operated. The other speaker terminal (SPKR) screws allow you to add an auxiliary speaker via a wire connection to get the same “Ding Dong” sound as the receiver. A volume control knob adjusts volume on receiver and auxiliary speaker and a different tone is generated depending on which transmitter (zone) is activated. For optimal reception the antenna will swivel 360°.
Additional Receivers: wireless (item 25-403) or wired (item 25-405) may be added.
Optional Extra Loud indoor Siren or Steady Tone Electronic sounder available for high noise areas, see item 60-206.
Product Instructions #DrivewayAlert, #EntryAlerts https://www.entryalertproducts.com/product/entry-way-alert-set-rodann-rxtx-2000a/
Multi-Purpose Programmable Timer Relay Module
This timer is easy to setup and use with all of our entry alert and driveway alarm products. Use the timer and optional higher current (500ma or 1 Amp) 12VDC adapter power supply to have higher power drawing accessories (up to 8 amps) activate for a specified length of time immediately after the sensor detects something and the alert receiver outputs an audible or visual alert. Programmable Timer Relay can be used on the 12VDC output of receivers or the Timer Relay can also be used on the Form C relay (NO/NC) channel/zone outputs of receivers to activate an accessory by channel/zone (additional 12VDC adapter power supply required for this application). Or use the timer to add a delay to the accessories activation. Timer activation or delay can be set from 1 second up to 60 minutes. With the easy to understand dip switches and versatility this timer allows you create the exact notification alert delay and or timed output (on) response you want. click for Data Sheet click for Product Instructions |
Wednesday, December 20, 2017
ENFORCER Extra Wireless Speaker, Seco-Larm
Additional wireless speaker / electronic chime. This speaker is to be used with Seco-Larm item 80-550, Wireless Entry Alert Beam System
Wireless Speaker (for E-931CS22RFCQ only):
Additional speaker / electronic chime.
No wires required – up to 328ft (100m) #AlarmSpeaker, #SecurityProducts #ALERTTYPE https://www.entryalertproducts.com/enforcer-extra-wireless-speaker-seco-larm/
Wireless Remote Entry Way Alert Chime System w/ 35 feet Beam
Wireless remote chime (up to 2000" line of sight transmission distance) entry way alert is activated when person or object passes through or across IR invisible beam. Beam sensor is powered by 12vdc adapter (included) on one side and by non-powered reflector on other side of entry way (separation of sensor and reflector can be from 1 foot up to 35 feet). Reflective Beam Entry Way Sensor includes 6" of cable and must be wired to 9V battery powered wall-mountable transmitter and included 12vdc adapter (instructions included). Transmitter settings allow one of four tones/chimes to be sent wirelessly up to 2000 feet (line of sight) away to Audible alert receiver with on/off switch and volume control. Chime selection (Classical, Westminster, Ding Dong, Whistle) only sounds twice when something passes through invisible IR beam. Multiple entry ways can be monitored with additional sensors ( item 80-403 ), power supplies ( item 60-300 ) and transmitters ( item 60-105 ). The additional entry ways can be set to individual unique chime settings if desired. Multiple wireless wall/desk receivers ( item 60-509 ) and or pagers ( item 60-103 ) may be used with single or multiple entry transmitters. Included receiver allows external sounders or accessories to be wired via a 12vdc output (400mA for selectable 4 seconds or 10 minutes) on channel/zone 1 and NO/NC relays (24vdc @ 3amps) for each of 4 channels/zones. Transmitters/receivers can be set to one of 256 frequency settings to avoid interference with nearby retailers using same system.
Optional Extra Loud indoor Siren or Steady Tone Electronic sounder available for high noise areas, see item 60-206.
Accessory power output (for each channel or the 12vdc output) can be increased with an optional 500mA or 1amp 12VDC adapter and/or the output duration time of any of the 4 individual NO/NC channel relays or the 12VDC output can be delayed or extended from 1 second to 60 minutes with the optional Programmable Relay Timer Module - (item 60-440).
Receiver Instructions
Transmitter Instructions
Reflective IR Beam Sensor Instructions
Addendum to Instructions
NOTE: This system is NOT plug"n play installation. Low voltage wiring required (click here for instructions included) and product set-up and mounting required. #ChimeAlert, #EntryAlerts https://www.entryalertproducts.com/product/wireless-remote-entry-way-alert-chime/
Dakota Indoor Motion Sensor / Receiver 2500, IRDCR-2500
The IRDCR-2500 is the newest addition to the family of motion sensors from Dakota Alert. This indoor PIR motion detector is compatible with all transmitters and receiver in the Dakota 2500 Series, and also has a range of up to 2000" depending on local terrain. Monitoring indoor locations has never been easier!
The passive infrared detector is able to monitor an area up to 100 degrees wide. This can be narrowed down to 20 degrees , or any degree in between, with the integral mask. The swivel mount makes it simple to adjust the sensing range from right to left, up to 80 degrees, and up and down up to 50 degrees. There are also three different sensitivity settings, allowing detection of a person up to 12, 25 or 40 feet away. Another option available: Have the sensor flash an LED or stay dark when a signal is sent. The IR-2500 is powered by one 9 volt battery and will have a battery life of about 12 months under normal conditions. There is also a low battery alert to notify you when it is time to replace the battery.
The IR-2500 is designed for indoor or light duty outdoor applications under an eave or awning or other protected location. Operating range temperature -30 F to 120 F. Great for home security, retail and business!
Alert Receiver Product Instructions
Motion Sensor Product Instructions #DakotaAlert, #MotionSensor https://www.entryalertproducts.com/product/dakota-indoor-motion-sensor-receiver-2500-irdcr-2500/
Tuesday, December 19, 2017
Siren, 30 Watts, 12VDC, 115db
30 Watt 12VDC Siren is weatherproof with a 115db sound level. The loudest that we carry. May requires1 Amp adapter (60-301) with the Dakota Driveway Alarm. Cone 6"x4" diameter x 8"long. #AlarmSystems, #Siren https://www.entryalertproducts.com/product/siren-30-watts-12vdc-115db/
Receiver for the Rodann Entrance Alert Set, RX-1000A
Extra Receiver for the Rodann® Entrance Alert Set, RX-1000A.
Optional Extra Loud indoor Siren or Steady Tone Electronic sounder available for high noise areas, see item 60-206. #AlarmSystem, #EntryAlerts https://www.entryalertproducts.com/product/receiver-for-the-rodann-entrance-alert-set-rx-1000a/
Monday, December 18, 2017
Curtain / Barrier Photobeam Sensors, Multiple, Seco-Larm
This device requires separate sounder, alert or chime system (and power supply for sensor and possibly chime). See items 1-9 on our accessories page.
These infrared photobeam curtain/barrier sensors are perfect for installation in windows, doorways, skylights, fence tops, any place where space is limited.
Suitable for indoor and outdoor perimeter security, the trigger is programmable for simultaneous breaking of any single or 2 adjacent beams. The design features rugged aluminum construction, and an anti-tamper circuit for triggering an alarm if power is cut or the end cap is removed.
No synchronizing wires are required and the LED alignment indicator makes installation easy. L-brackets and mounting hardware are included.
Manufacturers Web site
Note: Requires seperate sounding device and power supply.
NOTE: This device is not a stand alone system or plug’n play installation. Minor low voltage wiring required and additional items required to use.
For more information visit our entry alerts page #BestHomeSecuritySystem, #HomeSecurity #ALERTTYPE https://www.entryalertproducts.com/curtain-barrier-photobeam-sensors-multiple-seco-larm/
Wireless Entrance Alert Set with focused motion detector, Rodann, RX/TX-1000A
The "RX-1000A & TX-1000A Wireless Door Chime Set" is a highly versatile passive infrared (PIR) door announcer that senses the infrared emitted by a person or object crossing through its field of view. The RX-1000A & TX-1000A wireless door chime operates without reflectors or light beam projectors and therefore is immune to false alerts caused by transient light. You can use with door opened or closed. The RX-1000A & TX-1000A Wireless Door Chime is battery powered and does not require electrical wiring. This unique PIR makes the RX-1000A & TX-1000A wireless door chime set the best solution for virtually any installation. It can also be used on warehouse roll up doors, inside display cabinets, restricted area protection, or (patio, bedroom, bathroom) window alerting device.
NOTE: Receiver color may be WHITE
- Detects any Motion
- Infrared Sensor
- Wireless - Simple Installation
- Receiver has a volume control and plugs into a wall outlet anywhere up to 500" of the transmitter.
- Receiver uses 110 Volts
- Transmitter is battery powered
- 100% tested at the factory
- No Reflectors
- No Light Beams
- No False Alerts from transient light
- Up to 500 Foot Range
- Remote Receiver with Volume Control operates on 110V AC
- Alerts you with a pleasant electronic chime tone-four sound options
- Not affected by wind, heat, humidity or shadows
- Counters available
Optional Extra Loud indoor Siren or Steady Tone Electronic sounder available for high noise areas, see item 60-206.
Product Instructions
#EntryAlerts, #MotionDetector https://www.entryalertproducts.com/product/entrance-alert-set-rodann-rxtx-1000a/
Entry Way Alert Set. For outdoor or driveway applications, Rodann, RX/TX-2000A
Both transmitter and receiver have antennas that allow 360 degree rotation and pull away from sides of boxes. For best results in communication between transmitter and receiver it is ideal for the antennas to be on the same plane. Example: (If one antenna is pointing up in the vertical position, then the other antenna should be pointing up also. If one antenna is in the horizontal position, then the other antenna needs to be horizontal and pointing at each other for optimum reception). When it comes to distance in communication between transmitter and receiver environmental condition need to be considered. Line of sight without obstacles is ideal. Every tree, bush, fence, car, building in direct line of sight will reduce communication between units. These units should give you approximately 1000’. You may also add additional transmitters to one receiver or additional receivers to one transmitter.
TRANSMITTER
The outdoor weatherproof transmitter unit that can be either side or overhead mounted. A 9V replaceable battery is included and is already installed for your convenience. In the back of the unit there are six dip-switches. Numbers 1-4 control the communication security codes that must match the receiver. Numbers 5 & 6 on the transmitter identifies which of up to 4 transmitters (zones) is sending a driveway motion alert. There is an antenna that can rotate for optimal transmission to the receiver up to a realistic 1000 feet away. The driveway beam projection at 25 feet is 1 foot square and at 50 feet it is 2 feet square.
Additional wireless Sensor /Transmitters may be added (item 25-404).
RECEIVER
The indoor receiver has a plug-in 12VDC power supply with a 6 foot cord. The receiver may be placed on a counter top, table or hung on the wall. The electronic LED counter feature allows you to either count customers or count unexpected visitors / vehicles moving in your driveway. There is a reset button next to the counter, when pressed it will zero out the counter. This unit also has six dipswitches on the back of this unit. Numbers 1-4 must match transmitter. Number 5 controls the output of the 12VDC terminals on the back of the receiver with a one second or five second 12VDC output, Number 6 is not used. The terminal screws on the receiver back give you the option of adding a bell, buzzer, horn, siren, strobe or anything that is 12VDC operated. The other speaker terminal (SPKR) screws allow you to add an auxiliary speaker via a wire connection to get the same “Ding Dong” sound as the receiver. A volume control knob adjusts volume on receiver and auxiliary speaker and a different tone is generated depending on which transmitter (zone) is activated. For optimal reception the antenna will swivel 360°.
Additional Receivers: wireless (item 25-403) or wired (item 25-405) may be added.
Optional Extra Loud indoor Siren or Steady Tone Electronic sounder available for high noise areas, see item 60-206.
Product Instructions #DrivewayAlert, #EntryAlerts https://www.entryalertproducts.com/product/entry-way-alert-set-rodann-rxtx-2000a/
Friday, December 15, 2017
Curtain / Barrier Photobeam Sensors, Multiple, Seco-Larm
This device requires separate sounder, alert or chime system (and power supply for sensor and possibly chime). See items 1-9 on our accessories page.
These infrared photobeam curtain/barrier sensors are perfect for installation in windows, doorways, skylights, fence tops, any place where space is limited.
Suitable for indoor and outdoor perimeter security, the trigger is programmable for simultaneous breaking of any single or 2 adjacent beams. The design features rugged aluminum construction, and an anti-tamper circuit for triggering an alarm if power is cut or the end cap is removed.
No synchronizing wires are required and the LED alignment indicator makes installation easy. L-brackets and mounting hardware are included.
Manufacturers Web site
Note: Requires seperate sounding device and power supply.
NOTE: This device is not a stand alone system or plug"n play installation. Minor low voltage wiring required and additional items required to use. #AlarmSystem, #AlarmSystems https://www.entryalertproducts.com/product/curtain-barrier-photobeam-sensors/
Door / Window Sensor Alert Kit, Long Range, WD-434RTL
- Door/window sensor set.
- Magnetic type contact sensor.
- Notifies you when your door or window is open.
- Supervised Sensor: monitors the sensors and their battery condition automatically.
- HA-434RL receiver can work with up to 16 sensors in 4 zones.
- Comes with Alert and Alarm features.
- Built-in piercing 95db alarm siren will run for 3 minutes or until muted to reset.
- Alert mode has both audio beeping (approx 75db) and visual indicators distinguishing which of 4 zones/channels has the door or window open. Beeping will only stop when door/window is closed or mute button is pressed on receiver.
- Both audio and visual indicators.
- Easy to set up.
- FCC/IC approved.
- One year warranty.
ADDITIONAL Uses include: Front Door, Windows, Bedroom Windows, Patio Door
WD-434RTL Includes:
** One HA-434RL Household Alert® Receiver (AC/DC adapter included).
** One WD-434TL Door / Window Sensor (Lithium Battery included).
View Instructions
View Catalog Page
#DoorAlarm, #WindowSensor https://www.entryalertproducts.com/product/door-window-alert-kit-wd-434rtl/
Thursday, December 14, 2017
Voice Alert System 6 - Wireless Motion Sensor Monitor Alert
Voice Alert System-6 is a new annunciator system featuring wireless PIR sensors transmitters and a remote receiver/speaker base unit. Users record their own alert messages and are then notified with their own voice message when activity in a monitored is detected. Key applications include:
System-6 allows a maximum of six user recorded messages. Each message is specific to one zone. For instance, zone one could be for a driveway alarm -“Car coming up the driveway” while zone two could be for a sensor monitoring the back yard- “Alert! Child by the pool!” Perhaps a third sensor guards a side entrance against intruders. However, when this PIR detects movement, the base unit plays “Intruder on patio” and triggers a floodlight using one of four relays included on the base unit. System-6 can monitor all three zones simultaneously and still have three additional zones available when needed. Users can alter their messages and place the wireless sensors wherever they wish. Voice Alert System-6 sets up in minutes and can be completely customized to fit their individual needs. The wireless PIRs feature: all weather protection, adjustable mounting and sensitivity, and can send a signal 300 feet through walls and up to 1000 feet in open space. Includes the base unit and one wireless sensor. You may add additional sensors (Item# 30-212) to cover up to 6 areas total. Frequently Asked Questions for Voice Alert System Link to manufacturers website for more information |
Features
|
Wireless Entrance Alert Set with focused motion detector, Rodann, RX/TX-1000A
The "RX-1000A & TX-1000A Wireless Door Chime Set" is a highly versatile passive infrared (PIR) door announcer that senses the infrared emitted by a person or object crossing through its field of view. The RX-1000A & TX-1000A wireless door chime operates without reflectors or light beam projectors and therefore is immune to false alerts caused by transient light. You can use with door opened or closed. The RX-1000A & TX-1000A Wireless Door Chime is battery powered and does not require electrical wiring. This unique PIR makes the RX-1000A & TX-1000A wireless door chime set the best solution for virtually any installation. It can also be used on warehouse roll up doors, inside display cabinets, restricted area protection, or (patio, bedroom, bathroom) window alerting device.
NOTE: Receiver color may be WHITE
- Detects any Motion
- Infrared Sensor
- Wireless - Simple Installation
- Receiver has a volume control and plugs into a wall outlet anywhere up to 500" of the transmitter.
- Receiver uses 110 Volts
- Transmitter is battery powered
- 100% tested at the factory
- No Reflectors
- No Light Beams
- No False Alerts from transient light
- Up to 500 Foot Range
- Remote Receiver with Volume Control operates on 110V AC
- Alerts you with a pleasant electronic chime tone-four sound options
- Not affected by wind, heat, humidity or shadows
- Counters available
Optional Extra Loud indoor Siren or Steady Tone Electronic sounder available for high noise areas, see item 60-206.
Product Instructions
#EntryAlerts, #MotionDetector http://www.entryalertproducts.com/product/entrance-alert-set-rodann-rxtx-1000a/
Long Range Wireless Point to Point Entry Alert - Single Photobeam up to 50 feet
Wireless remote (up to 1500 feet; line of sight transmission distance) entry way alert or alarm is activated when person or object passes through the invisible line between the photobeam (single) sensor (transmitter) and receiver. Single photobeam requires power at each end of invisible beam (power adapters included). Separation of photobeam units can be from 3 feet up to 90 feet. Photobeam Sensor Receiver must be wired to 3vdc CR2 battery powered wall-mountable long range transmitter and included 12vdc adapters (instructions included). Transmitter settings allow one of four tones/chimes to be sent wirelessly up to 1500 feet (line of sight) away to Audible alert receiver with on/off switch and volume control. Chime selection (Classical, Westminster, Ding Dong, Whistle) only sounds twice when something passes through invisible IR beam. Multiple entry ways can be monitored with additional sensors ( item 80-400 ), power supplies ( item 60-300 ) and transmitters ( item 60-105 ). The additional entry ways can be set to individual unique chime settings if desired. Multiple wireless wall/desk receivers ( item 60-609 ) may be used with single or multiple entry transmitters.
When the receiver gets a signal from the transmitter one of 4 different tones (Classical, Westminster Chime, Ding Dong, Whistle) will sound for a few seconds. There is also a volume control so you can set the sound to the desired level. The receiver is also equipped with 4 (one for each zone) NO/NC (24vdc @ 3amps) relays and one 12 VDC (400mA max.) output terminal that can activate when a signal is received. The receiver can be user programmed so the 12VDC terminal and relays will activate for 1 second, 10 seconds, 60 seconds or 10 minutes. The tones will sound for several seconds.
Transmitters/receivers can be set to one of 256 frequency settings to avoid interference with nearby retailers using same system.
Optional Extra Loud indoor Siren or Steady Tone Electronic sounder available for high noise areas, see item 60-206.
What"s Included:
- Qty 1: Wireless 4 zone, chime selectable, relay output Receiver
- Qty 1: Single Photobeam Sensor - sender (transmitter) & receiver require power - up to 50 foot separation
- Qty 2: 12vdc 500ma transformer for Single Photobeam
- Qty 1: Long range transmitter
- Qty 1: 5 feet+, 2 conductor wire for wireless transmitter
What may be required:
- additional wire; depending on your installation.
- wire connectors - screw-on, butt, crimp, telephone/date/splice, or solder, insulating tape, etc.
Wireless Receiver Instructions
Long Range Transmitter Instructions
Single Photobeam Sensor, 50 feet max.
Addendum to Instructions
NOTE: This system is NOT plug"n play installation. Low voltage wiring required (click here for instructions included), product set-up, interconnect and mounting required*.
* Wire cutting, wire connecting, additional wire, wire connectors, screw drivers (all available at Home Depot, Lowes, Radio Shack, etc.) may all be required depending on your specific installation. This is all low-voltage wiring; however some people may require the services of an electrician, or someone with data/video/audio/telephone/tv wiring experience for proper installation.
Here are the specific instructions on how to interconnect all the items; we will only take returns on this system package (or pieces of it) if they are returned in brand new condition or a specific item is defective and needs replacing. #AlarmSystems, #EntryAlerts https://www.entryalertproducts.com/product/long-range-wireless-point-to-point-entry-alert-single-photobeam-50-feet/
Long Range Wireless Point to Point Entry Alert - Single Photobeam up to 50 feet
Wireless remote (up to 1500 feet; line of sight transmission distance) entry way alert or alarm is activated when person or object passes through the invisible line between the photobeam (single) sensor (transmitter) and receiver. Single photobeam requires power at each end of invisible beam (power adapters included). Separation of photobeam units can be from 3 feet up to 90 feet. Photobeam Sensor Receiver must be wired to 3vdc CR2 battery powered wall-mountable long range transmitter and included 12vdc adapters (instructions included). Transmitter settings allow one of four tones/chimes to be sent wirelessly up to 1500 feet (line of sight) away to Audible alert receiver with on/off switch and volume control. Chime selection (Classical, Westminster, Ding Dong, Whistle) only sounds twice when something passes through invisible IR beam. Multiple entry ways can be monitored with additional sensors ( item 80-400 ), power supplies ( item 60-300 ) and transmitters ( item 60-105 ). The additional entry ways can be set to individual unique chime settings if desired. Multiple wireless wall/desk receivers ( item 60-609 ) may be used with single or multiple entry transmitters.
When the receiver gets a signal from the transmitter one of 4 different tones (Classical, Westminster Chime, Ding Dong, Whistle) will sound for a few seconds. There is also a volume control so you can set the sound to the desired level. The receiver is also equipped with 4 (one for each zone) NO/NC (24vdc @ 3amps) relays and one 12 VDC (400mA max.) output terminal that can activate when a signal is received. The receiver can be user programmed so the 12VDC terminal and relays will activate for 1 second, 10 seconds, 60 seconds or 10 minutes. The tones will sound for several seconds.
Transmitters/receivers can be set to one of 256 frequency settings to avoid interference with nearby retailers using same system.
Optional Extra Loud indoor Siren or Steady Tone Electronic sounder available for high noise areas, see item 60-206.
What"s Included:
- Qty 1: Wireless 4 zone, chime selectable, relay output Receiver
- Qty 1: Single Photobeam Sensor - sender (transmitter) & receiver require power - up to 50 foot separation
- Qty 2: 12vdc 500ma transformer for Single Photobeam
- Qty 1: Long range transmitter
- Qty 1: 5 feet+, 2 conductor wire for wireless transmitter
What may be required:
- additional wire; depending on your installation.
- wire connectors - screw-on, butt, crimp, telephone/date/splice, or solder, insulating tape, etc.
Wireless Receiver Instructions
Long Range Transmitter Instructions
Single Photobeam Sensor, 50 feet max.
Addendum to Instructions
NOTE: This system is NOT plug"n play installation. Low voltage wiring required (click here for instructions included), product set-up, interconnect and mounting required*.
* Wire cutting, wire connecting, additional wire, wire connectors, screw drivers (all available at Home Depot, Lowes, Radio Shack, etc.) may all be required depending on your specific installation. This is all low-voltage wiring; however some people may require the services of an electrician, or someone with data/video/audio/telephone/tv wiring experience for proper installation.
Here are the specific instructions on how to interconnect all the items; we will only take returns on this system package (or pieces of it) if they are returned in brand new condition or a specific item is defective and needs replacing. #AlarmSystems, #EntryAlerts https://www.entryalertproducts.com/product/long-range-wireless-point-to-point-entry-alert-single-photobeam-50-feet/
MACE Motion Alert Motion Detector With Security Alarm, M80200
Motion activated alarm and door chime. Dual-purpose passive infrared alarm detects movement in any selected area. Two modes of operation allows it to function as a door chime and also a 110 dB alarm. The door chime is useful for alerting you of someone’s presence. The alarm’s programmable keypad offers added security since you will have control over the access code. Adjustable sensor head rotates so you can selectively choose the area covered. A low battery indicator tells you when the battery needs to be replaced. Comes with complete mounting kit and instructions. 9 volt battery (sold separately). #AlarmSystem, #MotionDetector http://www.entryalertproducts.com/product/mace-motion-alert-motion-detector-with-security-alarm-m80200/
Twin Photobeam Detector, In / Outdoor, Seco-Larm
This device requires separate sounder, alert or chime system (and power supply for sensor and possibly chime). See items 1-9 on our accessories page.
ENFORCER Long Range Photobeam Detectors are easy-to-install with laser beam alignment and provide extended range. Designed to provide reliable perimeter security both indoors and outdoors.
Product Info sheet
Installation Manual
Manufacturers Web site
Note: Requires separate sounding device and power supply.
NOTE: This device is not a stand alone system or plug"n play installation. Minor low voltage wiring required and additional items required to use.
Features
- Built-in laser beam alignment system speeds accurate, reliable positioning.
- Twin infrared beams provide reliable perimeter security, minimizing false alarms from falling leaves, birds, etc.
- Lensed optics reinforce beam strength & provide excellent immunity to false alarms due to rain, snow, mist, etc.
- Weatherproof, sunlight-filtering case for indoor & outdoor use.
- Anti-frost system so that beam functions even in extreme conditions.
- Automatic input power filtering with special noise rejection circuitry.
- N.C./N.O. alarm output.
- N.C. tamper circuit included.
- Non-polarized power inputs.
- Quick, easy installation with built-in laser beam alignment system.
- Interruption time adjustable for nearly all situations.
Enforcer Single Photobeam Sensor, 50 Ft, Seco-Larm
This device requires separate sounder, alert or chime system (and power supply for sensor and possibly chime). See items 1-9 on our accessories page.
The Seco-Larm Enforcer Single Photo beam Motion Sensor is the easy-to-install way to protect large indoor and outdoor openings as well as allow easy exit from areas protected by access control equipment. When used as part of an alarm system, it can detect vehicles along a driveway or entering a factory or similar site.
Typical Applications
- Gates or garage doors
- Overhead doors
- Parking lots
- Driveways
- Warehouses
Product Info sheet
Installation Manual
Manufacturers Web site
Note: Requires separate sounding device and power supply.
NOTE: This device is not a stand alone system or plug"n play installation. Minor low voltage wiring required and additional items required to use. #AlarmSystems, #PhotoBeamSensor https://www.entryalertproducts.com/product/enforcer-single-photobeam-sensor-50-ft-seco-larm/
Home Security - Secure Your Home
Home Security - Secure Your Home And Family With This Useful Information
If home security is a topic of curiosity, you have come to the right place. There"s no reason for you to settle when making a very important decision. You must be in control when it comes to this decision. This is made easy if you have the right information. Read on to learn about your options.
When you buy a new house, change the locks. You will want to have a unique combination to stay secure. Having a locksmith replace the locks will ensure that no strangers have a key. Also, you can contact a locksmith if you ever misplace your keys.
Be brave! Talk to your neighbors. Watch out for their homes, and ask them to do the same for you. Do not ignore gossip either. While this is unorthodox, it may clue you into a possible home security threat.
Have lights that are motion-sensor installed. They"ll flip on when people walk within a certain distance of your house. Motion-sensitive lights will alert you to movement and deter people who want to break into your home. But keep in mind that the bulbs to the security light should be routinely changed to ensure that the deterrent system functions properly.
Switch your locks. Perhaps your roommate left town or you have gone through a messy divorce, and you need to feel that the home is safe. Changing locks is not very expensive and should be done within a few hours.
After installing a security system in your home, make sure any wires are hidden. Exposed wires make it easy for an intruder to cut them and disable the alarm. Instead, make sure the wires are hidden. You"ll be safer.
If you have purchased any large and/or expensive items, do not throw the boxes away until the day before the trash man is scheduled to come. Having these boxes nearby can tell robbers what kind of merchandise you"ve got in your house.
Replace rotten wood on your door frame. Anybody wanting to break into your house can just pry off rotted wood and get inside. When you see that wood is beginning to rot, replace it with new wood for better home safety.
Your flashlights should always be equipped with good, working batteries. Flashlights are key because they allow you to move around if an emergency should arise. Your whole family should be trained on the proper use and maintenance of flashlights.
If you"re going to hire a company that provides home security, read everything in the contract before you sign it. You need to find out about hidden costs, such as cancellation fees in case you want to cancel your contract before it expires. You want to try to avoid these fees whenever possible, so make sure you are aware of them.
Always use online resources to identify the very best home security firm. Look at many websites and read customer reviews about the various services. Then, you can choose a top three to contact and compare details and pricing.
As you work on your home"s landscape, don"t forget about safety. You should have a clear view out of all your windows and an unobstructed path to any doors. If these things can be seen by the naked eye, they won"t offer hiding places to potential criminals. Utilize shrubs and trees farther away in order to add beauty to your home while keeping it safe.
You should find out how many years of experience your home security service has. Look for a security company that is well-established and has extensive experience in the industry. It also ensures they"re not a fly-by-night firm.
Have a home security company come to your house and come up with a system that best suits your needs. You need some features which other families may wish to do without. If you are able to secure a company willing to tailor a system to your needs, there is a good chance that you will be satisfied.
Think about your specific needs and risks prior to investigating security systems. Although automated electronic systems are powerful, they"re not necessarily the cost-effective solution for every home. Some neighborhoods may do better with self-defense classes or having a dog, while others may require the best home security technology you can get. Think about your risk factor when making a decision.
Make sure that whoever is getting your mail while you are on vacation also retrieves any fliers left on the door. Burglars often put fliers on the door to see if the owner removes them. If their fliers are not moved, the crook knows the home is unattended.
Now that you have learned about your options, you can make the right decision. Installing the right type of service and system as well as having the right type of knowledge is very important. Protect your home and your family by applying what you"ve learned from this article.
Entry Alert System Entry Digital Counter, Seco-Larm
- Automatically tracks how often the Entry Alert System With Chime (E-931CS22RRCQ or E-931CS22RFCQ) is triggered.
- Push buttons to manually add to or subtract from counter, or to reset to zero.
- Plugs into speaker - no wiring needed.
- Other applications: offices, schools, warehouse, vehicle detection, etc.
Includes the following:
- Digital Counter.
- Mounting hardware.
- Connection cord with plugs. #EntranceAlert, #EntryAlerts https://www.entryalertproducts.com/product/digital-counter-seco-larm/
Entrance Alert Set, Rodann, TX/RX-1000A
Additional Receivers RX-1000A and/or Sensor / Transmitters TX-1000A may be added! Receiver RX-1000A (item 25-303) and Transmitter (item 25-304)
An additional wired speaker can be also added to the wireless receiver; it"s item number is 25-405
Optional Extra Loud indoor Siren or Steady Tone Electronic sounder available for high noise areas, see item 60-206.
- Detects any Motion
- Infrared Sensor
- Wireless - Simple Installation
- Receiver has a volume control and plugs into a wall outlet anywhere up to 500" of the transmitter.
- Receiver uses 110 Volts
- Transmitter is battery powered
- 100% tested at the factory
- No Reflectors
- No Light Beams
- No False Alerts from transient light
- Up to 500 Foot wireless alert signal transmission Range
- Remote Receiver with Volume Control operates on 110V AC
- Alerts you with a pleasant electronic chime tone-four sound options
- Not affected by wind, heat, humidity or shadows
- Counters available
#EntryWayAlert https://www.entryalertproducts.com/product/entrance-alert-set-rodann-tx-rx-1000a/
Emergency Alert Strobe / Flashing Light, 12VDC (6~24VDC)
- For "informative" general signaling requirements
- Incorrect polarity cannot damage circuit or draw current
- Easy 2-wire installation, regardless of voltage. Also, if the strobe light is being powered by a battery, as the battery is drained the strobe light will continue to function
- Low current consumption with long operating lifespan of over 300 continuous hours (2,000,000 flashes)
- Includes choice of amber, blue, clear, or red lens
- Lens is made of high-impact resistant acrylic, case of high-impact resistant ABS plastic
- The SECO-LARM strobe light comes with a protective inner cover. This protects the high-voltage xenon tube when the colored lens has been removed
- Use in temperature ranging from -22ºF (-30ºC) to 140ºF (60ºC)
- SL-126-A24Q -- For 6- to 24-Volt use
Rodann Driveway / Entry Alert Receiver, RX-2000A
The indoor driveway / entry alert receiver has a plug-in 12VDC power supply with a 6 foot cord. The receiver may be placed on a counter top, table or hung on the wall. The electronic LED counter feature allows you to either count customers or count unexpected visitors / vehicles moving in your driveway. There is a reset button next to the counter, when pressed it will zero out the counter. This unit also has six dip-switches on the back of this unit. Numbers 1-4 must match transmitter. Number 5 controls the output of the 12VDC terminals on the back of the receiver with a one second or five second 12VDC output, Number 6 is not used. The terminal screws on the receiver back give you the option of adding a bell, buzzer, horn, siren, strobe or anything that is 12VDC operated. The other speaker terminal (SPKR) screws allow you to add an auxiliary speaker via a wire connection to get the same “Ding Dong” sound as the receiver. A volume control knob adjusts volume on receiver and auxiliary speaker and a different tone is generated depending on which transmitter (zone) is activated. For optimal reception the antenna will swivel 360°.
Optional Extra Loud indoor Siren or Steady Tone Electronic sounder available for high noise areas, see item 60-206. #AlarmSystems, #DrivewayAlert https://www.entryalertproducts.com/product/receiver-for-the-rodann-driveway-entry-alert-rx-2000a/
Wednesday, December 13, 2017
Siren, 15 watts, 12VDC, 110db
15 Watt 12VDC Siren is weatherproof with a 110db sound level. Simply connects to the relay output of an Alert Receiver. Requires 1 Amp adapter (60-301). Cone 3.5" diameter x 4" long. #AlarmSystems, #Siren http://www.entryalertproducts.com/product/siren-15-watts-12vdc-110db/
Wireless PIR Indoor Motion Sensor, Dakota IR-2500
The IR-2500 is the newest wireless PIR indoor motion alarm from Dakota Alert. With a wireless range of up to 2000 feet* and full compatibility with any of our 2500 Series transmitters or receivers, the IR-2500 will allow you to monitor many indoor locations that were difficult before. The passive infra red detector is able to monitor an area up to 100º wide. With the integral mask, the detection area can be narrowed down to 20º or anywhere in between. With the swivel mount, the IR-2500 sensor can be adjusted right to left up to 80º and up and down up to 50º. With three different sensitivity settings, the IR-2500 can detect a person up to 12 feet, 25 feet or 40 feet away. The sensor can also be set to flash an LED or stay dark when a signal is sent. The IR-2500 is powered by one 9 volt battery and will have a battery life of about 12 months under normal conditions. There is also a low battery alert to notify you when it is time to replace the battery. The IR-2500 is designed for indoor or light duty outdoor applications under an eave or awning or other protected location. Operating range -30º F to 120º F.
Motion Sensor Product Instructions #AlarmSystems, #MotionSensor http://www.entryalertproducts.com/product/indoor-motion-sensor-ir2500/
Tuesday, December 12, 2017
Voice Alert System 6 Motion Sensor / Transmitter, VA6000T
Motion sensor for your voice Alert System 6 annunciator (Item #30-211). #AlarmSystems, #VoiceAlert http://www.entryalertproducts.com/product/voice-alert-6-motion-sensor-va6000t/
Optex Wireless 1000 Door Contact / Wireless Transmitter, TC-10U
The Optex Wireless 1000 (TC-10U) Door Contact / Wireless Transmitter is designed for indoor and outdoor use (not in direct rain). It can be installed on doors and windows. This Contact / Transmitter features a low battery signal and is powered by a CR123 - 3V lithium battery.
The TC-10U is a battery-powered door / window contact and wireless transmitter for the RCTD-20U (Wireless 2000). When used as a wireless transmitter and installed in the backbox of any of OPTEX"s battery operated detectors, extended detection range and wireless notification to your RC-20U chime box is achieved. Instantly monitor larger areas with minimal false alarms for a greater sense of protection. When used as a door contact, the TC-10U will send a signal to the RC-20U receiver chime box. This gives the user a notification when the door is opened, and is perfect for high traffic areas around entrances where an above door sensor is not practical.
Features
- Can be installed on Door/Window
- Weather proof structure (not rain proof)
- Over 8 million wireless codes possible (eliminates interference)
- Low battery signal
Voice Alert 6 Extra Receiver Speaker, VA6000R
Monday, December 11, 2017
Wired 8 ohm Speaker for Rodann Alert wireless Receivers
Additional wired Speaker for Rodann Alert wireless Receivers, RX-1000A and RX-2000A. #AlarmSystems, #WeatherProofSpeaker http://www.entryalertproducts.com/product/additional-wired-speaker-for-rodann-alert-wireless-receivers/
Rodann Driveway / Entry Alert Receiver, RX-2000A
The indoor driveway / entry alert receiver has a plug-in 12VDC power supply with a 6 foot cord. The receiver may be placed on a counter top, table or hung on the wall. The electronic LED counter feature allows you to either count customers or count unexpected visitors / vehicles moving in your driveway. There is a reset button next to the counter, when pressed it will zero out the counter. This unit also has six dip-switches on the back of this unit. Numbers 1-4 must match transmitter. Number 5 controls the output of the 12VDC terminals on the back of the receiver with a one second or five second 12VDC output, Number 6 is not used. The terminal screws on the receiver back give you the option of adding a bell, buzzer, horn, siren, strobe or anything that is 12VDC operated. The other speaker terminal (SPKR) screws allow you to add an auxiliary speaker via a wire connection to get the same “Ding Dong” sound as the receiver. A volume control knob adjusts volume on receiver and auxiliary speaker and a different tone is generated depending on which transmitter (zone) is activated. For optimal reception the antenna will swivel 360°.
Optional Extra Loud indoor Siren or Steady Tone Electronic sounder available for high noise areas, see item 60-206. #AlarmSystems, #DrivewayAlert http://www.entryalertproducts.com/product/receiver-for-the-rodann-driveway-entry-alert-rx-2000a/
Optex RC-20U Wireless 2000 Receiver / Alert Chime
The RC-20U is the receiver / chime for the RCTD-20U (Wireless 2000). The device is powered by a AC adapter (included), and up to nine TD-20U"s can be added to one RC-20U receiver. (With an additional three added to a latching zone) In addition, the RC-20U includes a Form-C relay for activating additional devices such as lights, a camera, door lock, ect.
The RC-20 Receiver can be placed in any room of your home or business to notify you of customers or visitors. Additional receivers can be purchased to expand your Optex Driveway Annunciator System. The RC-20 Receiver includes volume control, an on/off switch, and three different chime sounds to choose from. Up to 12 TD-20 sensor/transmitters can be programmed to this RC-20 receiver, giving you the ability to monitor several different locations! As well, the RC-20 receiver and the TS10 portable handheld transmitter together provide an excellent wireless doorbell system.
Product Instructions
Features
- Low battery indication by tone (RC-20) and LED (all models) tells you when to replace batteries and prevents malfunctions.
- Receiver mounts on wall or desktop.
- Optimal antenna design and fine RF tuning achieve a high signal to noise rate, ensuring long range and consistent operation.
Friday, December 8, 2017
Mini Alert Motion Detector - Infrared Sensor Alarm / Chime
This infrared motion detector alarm sounds an 80 db alarm whenever someone comes within the range of the infrared zone.
- The zone detection coverage is 80 degrees horizontally out to 8 meters and 20 degrees vertically.
- 30 second delay allows you to move out of the way before the alarm or chime becomes activated.
Alarm Mode
- It works by means of Passive Infrared motion sensor which it detects a moving human body within a range of 8 meters x 80 degrees.
- The alarm sounds automatically when any human body approaches the detected zone.
- 20 degree vertical coverage allows you to position the alarm so pets will not set off alarm.
- A siren will sound for one minute then shut off automatically and reset itself. Visitor Chime Mode - A pleasant "Ding Dong" melody sounds automatically to greet your visitor when they approach the detected zone.
- Uses 3 "AA" batteries, not included. LED indicator on face of infrared sensor alarm lights up when batteries are low and need replacing.
- Size: 2 3/4" x 1-1/2" x 4-1/2"
WALL MOUNTABLE
Installation
- Mount the adjustable angle wall mount bracket in the desired location with screw and screw anchor (provided).
- Adjust the Mini Alert alarm to the desired detection direction and hold it in position by tightening the screw at the bracket.
This infrared motion sensor alarm works great for announcing vistors to your home or to protect certain areas.
The loud, motion activated alarm alerts you whenever someone breaks into the detection zone. Use at home or use at the office. #InfraredSensor, #MotionDetector http://www.entryalertproducts.com/product/mini-alert-motion-detector/
Long Range Wireless Point to Point Entry Alert - Twin Photobeam, up to 90 feet
Wireless remote (up to 1500 feet; line of sight transmission distance) entry way alert or alarm is activated when person or object passes through the invisible line between the twin photobeam sensor (transmitter) and receiver. Twin photobeam requires power at each end of invisible beam (power adapters included). Separation of photo beam units can be from 3 feet up to 90 feet (or greater with optional Photobeams - contact us). Photobeam Sensor Receiver must be wired to 3vdc CR2 battery powered wall-mountable long range transmitter and included 12vdc adapters (instructions included). Transmitter settings allow one of four tones/chimes to be sent wirelessly up to 1500 feet (line of sight) away to Audible alert receiver with on/off switch and volume control. Chime selection (Classical, Westminster, Ding Dong, Whistle) only sounds twice when something passes through invisible photo beam. Multiple entry ways can be monitored with additional sensors ( item 80-402 ) or similar, power supplies ( item 60-300 ) and transmitters ( item 60-105 ). The additional entry ways can be set to individual unique chime settings if desired. Multiple wireless wall/desk receivers ( item 60-609 ) may be used with single or multiple entry transmitters.
When the receiver gets a signal from the transmitter one of 4 different tones (Classical, Westminster Chime, Ding Dong, Whistle) will sound for a few seconds. There is also a volume control so you can set the sound to the desired level. The receiver is also equipped with 4 (one for each zone) NO/NC (24vdc @ 3amps) relays and one 12 VDC (400mA max.) output terminal that can activate when a signal is received. The receiver can be user programmed so the 12VDC terminal and relays will activate for 1 second, 10 seconds, 60 seconds or 10 minutes. The tones will sound for several seconds.
Transmitters/receivers can be set to one of 256 frequency settings to avoid interference with nearby retailers using same system.
Optional Extra Loud indoor Siren or Steady Tone Electronic sounder available for high noise areas, see item 60-206.
What"s Included:
- Qty 1: Wireless 4 zone, chime selectable, relay output Receiver
- Qty 1: Twin Photobeam Sensor - sender (transmitter) & receiver require power - up to 90 foot separation
- Qty 2: 12vdc 500ma transformer for Twin Photo beam
- Qty 1: Long range transmitter
- Qty 1: 5 feet+, 2 conductor wire for wireless transmitter
What may be required:
- additional wire; depending on your installation.
- wire connectors - screw-on, butt, crimp, telephone/date/splice, or solder, insulating tape, etc.
Wireless Receiver Instructions
Long Range Transmitter Instructions
Twin Photobeam Detector, 90 feet max.
Addendum to Instructions
NOTE: This system is NOT plug"n play installation. Low voltage wiring required (click here for instructions included), product set-up, interconnect and mounting required*.
* Wire cutting, wire connecting, additional wire, wire connectors, screw drivers (all available at Home Depot, Lowes, Radio Shack, etc.) may all be required depending on your specific installation. This is all low-voltage wiring; however some people may require the services of an electrician, or someone with data/video/audio/telephone/tv wiring experience for proper installation.
Here are the specific instructions on how to interconnect all the items; we will only take returns on this system package (or pieces of it) if they are returned in brand new condition or a specific item is defective and needs replacing. #EntryAlerts, #WirelessTransmitter http://www.entryalertproducts.com/product/long-range-wireless-point-to-point-entry-alert-twin-photobeam-90-feet/
Thursday, December 7, 2017
Receiver for the Rodann Entrance Alert Set, RX-1000A
Extra Receiver for the Rodann® Entrance Alert Set, RX-1000A.
Optional Extra Loud indoor Siren or Steady Tone Electronic sounder available for high noise areas, see item 60-206. http://www.entryalertproducts.com/product/receiver-for-the-rodann-entrance-alert-set-rx-1000a/
Voice Alert Wireless Door Entry Announcer, VA6DEA
Voice Alert System-6 allows voice-recorded messages to identify activity for up to six monitored zones. The Voice Alert System-6 uses wireless sensors (contact closure / motion / etc.) that send a wireless signal up to 1000" line of sight (or up to 300" inside) to an indoor receiver/speaker (Base Unit).
When a wireless sensor is activated a radio signal is sent from the wireless transmitter to the remote Base Unit. A custom message, which you"ve recorded in your own voice for that specific zone, is played on the Base Unit. One of four form "C" relays (NO/NC dry on/off switches) attached to the Base Unit can optionally be triggered (see example below). With its ability to secure up to six separate zones, each with its own customized recorded message in your own voice, Voice Alert is the most flexible system available.
Users can place the wireless transmitter sensors wherever needed and alter their recorded messages at any time. Voice Alert System-6 sets up in minutes and can be completely customized to handle tough wiring situations. Multiple base units may also be used to trigger alerts in two or more areas simultaneously.
The TXPCBB transmitter sends a radio signal by input from either Normally Open (NO) or Normally Closed (NC) devices. An included magnetic door contact sensor with 2" of wire is included. The small magnet mounts on the door and the small wired sensor mounts opposite the magnet on the door frame and it connects (via the included 2" of wire) to the NC (normally closed) terminals on the transmitter.
The transmitter box is housed in a water-tight NEMA box, the TXPCBB has a radio transmission range of up to 1000" line of sight or up to 300" through walls. The NEMA box will handle all environments and includes mounting tabs to accommodate a variety of mounting options.
The TXPCBB transmitter is powered by a 9V battery. An alkaline battery has a battery life of over one year and a lithium 9V battery will last three to five years. The system includes a "low battery" feature designed to notify the user when a battery voltage approaches a low battery threshold.
Manufacturer"s Website
Receiver Instructions
Wireless Transmitter Instructions #AlarmSystem, #MotionEntry, #VoiceAlert http://www.entryalertproducts.com/product/voice-alert-wireless-door-entry-announcer-va6dea/
Whistle Alert, Electronic, 12VDC
Mini Whistle for annunciation in remote areas, simply connects to a 12 Volt output of the any Alert Receiver or requires a minimum 500 ma adapter (60-301) if used on the relay output of a receiver. 0.87" diameter x 0.37" high.
The whistle can also be installed in any alarm or doorbell system that uses 2-strand doorbell wire. When activated, it sounds a loud whistle for approximately 4 seconds.
- Sounds loud whistle for 4 seconds when activated
- Red and black leads connect to 12VDC output
Wednesday, December 6, 2017
Long Range Wireless Door Contact, UTDC-2500
Additional Magnetic Door Contact and Long Range transmitter for (item 00-210), Wireless Remote Door Entry Alert (UTDCR-2500) #EntryAlerts, #WirelessTransmitter http://www.entryalertproducts.com/product/long-range-wireless-door-contact-utdc-2500/
Voice Alert 6 Extra Receiver Speaker, VA6000R
Tuesday, December 5, 2017
Siren Mini Piezo, 12VDC
Mini Piezo 12 VDC Siren has similar sound to a domestic smoke alarm. Piercing 105 dbA mini siren simply connects to the, 12 Volt output of any Receiver or can be used on the relay output of an Alert receiver (requires 500 ma adapter item 60-301 if used on the relay output). #AlarmSystems, #Siren http://www.entryalertproducts.com/product/siren-mini-piezo-12vdc/
Motion Sensor / Transmitter, Skylink HA-434TL
- Alerts you when motion is detected surrounding your garage, home or business.
- Supervised Sensor: monitors the sensors and their battery condition automatically.
- Motion detecting range: 40 feet.
- Operating range: up to 800 feet line of sight.
- Easy to set up.
- FCC/IC approved.
- One year warranty.
Monday, December 4, 2017
Optex Wireless 1000 Door Contact / Wireless Transmitter, TC-10U
The Optex Wireless 1000 (TC-10U) Door Contact / Wireless Transmitter is designed for indoor and outdoor use (not in direct rain). It can be installed on doors and windows. This Contact / Transmitter features a low battery signal and is powered by a CR123 - 3V lithium battery.
The TC-10U is a battery-powered door / window contact and wireless transmitter for the RCTD-20U (Wireless 2000). When used as a wireless transmitter and installed in the backbox of any of OPTEX"s battery operated detectors, extended detection range and wireless notification to your RC-20U chime box is achieved. Instantly monitor larger areas with minimal false alarms for a greater sense of protection. When used as a door contact, the TC-10U will send a signal to the RC-20U receiver chime box. This gives the user a notification when the door is opened, and is perfect for high traffic areas around entrances where an above door sensor is not practical.
Features
- Can be installed on Door/Window
- Weather proof structure (not rain proof)
- Over 8 million wireless codes possible (eliminates interference)
- Low battery signal
EZ Tone Entrance Alert Door Chime, beige / light gray color
The EZ Tone Door Chime never needs batteries or electricity and it can easily be installed on all types of doors and jambs. When the door is opened, a magnetic striker hits the toned chime bar and produces a pleasant, audible tone. It can be used in both commercial and residential applications. Once installed no maintenance is ever required.
The EZTone is designed for doors that swing only one direction.
Easy instructions, mounting templates and hardware included.
EZTone customers include, Subway, Blockbuster, Winn-Dixie, US Postal Service, Kentucky Fried Chicken, Dollar General Stores, Little Caesars, and many professional offices nationwide. The E-Z Tone Door Chime can usually be installed within 15 minutes, and has a long, maintenance free life.
Instructions #AlarmSystems, #DoorChime http://www.entryalertproducts.com/product/ez-tone-entrance-alert-door-chime-beige/